background image

 

                

www.elakeside.com

  

4900 W. Electric Ave. West Milwaukee WI. 53219

                                             

414-902-6400

 

 

 

 

**** INSTALLATION INSTRUCTIONS - SAVE THESE INSTRUCTIONS **** 

 

 

 

 

 

 

 

 

 

 

Part I. General Installation and Use 

 

Prior to installation, inspect product - including all electrical equipment - for possible 
shipping damage. Do not install any products showing cracks, de-lamination or other 
damage. Do not substitute any other parts for fasteners or other items supplied with the 
product. Contact the factory if spare parts are needed.  

 

Part II. Eectrical Installation 

 

WARNING

 

To Prevent Possible Electric Shock or Product Damage, Read and Observe All 
Instructions and Product Markings Prior to Installation and Use of These Products 

 

Ratings: 120 Volts, 13.4 Amps, 60 Hz . for heated water units; 0.9 Amps for non-heated  
Use a 15 Amp Branch Circuit unless instructed otherwise by local authorities. 

 

Part III.  Operation 

 

The Mobile Hand Washing Stations must be properly set up prior to use.  With the unit 
unplugged from the power supply, the following must be done: 

 

1. 

Open the compartment door to expose the water tanks and controls. 

2. 

Remove the fresh water tank and the waste water tank. 

3. 

Empty the waste water tank and rinse any residue out of the tank. 

4.  

Fill the fresh water tank with clean, potable water. 

5. 

Reinstall the empty waste water tank and the full fresh water tank. 

6. 

Inspect the interior for loose hoses, sings of leaking, disconnected, cracked, or 
damaged wires.  DO NOT USE UNIT if anything is not correct.  Fix or repair prior to 
use. 

7. 

Plug unit into properly grounded outlet and open faucet to test pump operation.  
Water may not be hot if the unit has been unplugged for a period of time. If water 
does not flow from the faucet, check the indicator light on the GFCI.  If the light is not 
on, reset the GFCI by pushing the reset button in on the face of the GFCI. 

8. 

Close door to place unit into operation.  Heated units may require a 

½

 hour pre heat 

for initial run. 

9. 

Refill the soap dispenser as needed by lifting the dispenser up and out of the holder 
and pouring the soap into the holder. 

 

 
 
 
 
 
 
 

Summary of Contents for 9600 Series







Reviews: