background image

 

10HP

 

Stationary

 

Dust

 

Cyclone

 

Manual

 

6

Indicates a potentially hazardous situation which, if not avoided, 

may result in minor or moderate injury. 

 
 
 

Used without the safety alert symbol indicates potentially hazardous 

situation which, if not avoided, may result in property damage. 
 

 
GENERAL SAFETY RULES 
 

 

WARNING FAILURE TO FOLLOW THESE RULES MAY RESULT 

IN SERIOUS PERSONAL INJURY. 
 
FOR YOUR OWN SAFETY, READ AND UNDERSTAND THE INSTRUCTION MANUAL 
BEFORE OPERATING THE MACHINE. 
Learn the unit’s application and limitations as well 
as the specific hazards peculiar to it. 

 
KEEP WORK AREA CLEAN. 
Cluttered areas and benches invite accidents. 
 
DON’T USE IN DANGEROUS ENVIRONMENT. 
Don’t use this unit in damp or wet 
locations, or expose it to rain. Keep work area well-lighted. 

 
KEEP CHILDREN AND VISITORS AWAY. 
All children and visitors should be kept a safe 
distance from work area. 
 
DISCONNECT UNIT 
before servicing. 

 
CHECK DAMAGED PARTS. 
Before further use of the unit, properly repair or replace any 
part that is damaged.  
 

 FAILURE TO FOLLOW THESE RULES MAY RESULT IN 

SERIOUS INJURY. 
 

ADDITIONAL SAFETY FOR DUST COLLECTORS 

  

 
Intended use. 
This dust collector is only intended for collecting wood dust and chips from 
woodworking machines. Do not use this dust collector to collect metal, dirt, pebbles, 
drywall, asbestos, lead paint, silica, liquids, aerosols, or any flammable, combustible, or 
hazardous materials. 

Summary of Contents for T Flux 10

















































Reviews: