-11-
www.igmtools.com
Pic. 33
Step 30: Lift the foot peddle bar. Align the Octagon drum window to the
center point of the drum lid and push the drum in. Lower the foot peddle
bar (s) to seal the drum tight for normal machine operation.
Pic. 34
Step 31: Make sure when aligning the drum that both the left and right
side lift plates are over the topping on the foot peddle bar assembly before
lifting the foot peddle bar up. When not aligned, the drum will not be fully
sealed and will interfere with the air flow.
Pic. 35
Step 32: Install the Remote Switch Box to the switch plate on the motor
using hex bolts (4) 6 mm*19 mm and flat washers (4) 6 mm*OD19*2T.
3HP Mobile Dust Cyclone Manual
28
Step Twenty Eight: Insert the plastic bag inside the Octagon drum. Open and
spread out the plastic bag to the corners and edges
Step Twenty Nine:
Place the drum insert inside over the plastic bag in the
Octagon drum.
Drum insert
3HP Mobile Dust Cyclone Manual
29
Step Thirty: Lift the foot peddle bar. Align the Octagon drum window to the center
point of the drum lid and push the drum in. Lower the foot peddle bar (s) to
seal the drum tight for normal machine operation.
Step Thirty One:
Make sure when aligning the drum that both the left and right
side lift plates are over the topping on the foot peddle bar assembly before lifting
the foot peddle bar up. When not aligned, the drum will not be fully sealed and
will interfere with the air flow.
1
2
3
3HP Mobile Dust Cyclone Manual
29
Step Thirty: Lift the foot peddle bar. Align the Octagon drum window to the center
point of the drum lid and push the drum in. Lower the foot peddle bar (s) to
seal the drum tight for normal machine operation.
Step Thirty One:
Make sure when aligning the drum that both the left and right
side lift plates are over the topping on the foot peddle bar assembly before lifting
the foot peddle bar up. When not aligned, the drum will not be fully sealed and
will interfere with the air flow.
1
2
3
Pic. 36
Step 33: Take the paddle and paddle branch and assemble together
using hex bolts (4) 6 mm*16 mm, flat washers (4) 6 mm*OD19*1T and
nuts (4) 6 mm.
Pic. 37
Step 34: Assemble the two paddle and paddle branch assemblies to the
rotation shaft using hex bolts (4) 6 mm*16 mm, flat washers (4) 6
mm*OD19*1T and nuts (4) 6 mm.
Pic. 38
Step 35: Insert the rotation shaft assembly into the canister filter. Slightly
bend the paddles to get them into the canister filter.
Pic. 39
Step 36: Assemble the canister filter to the dust chute. Tighten the band
clamp and adjust the tightness accordingly to ensure the canister filter is
tightly fitted onto the dust chute.
3HP Mobile Dust Cyclone Manual
30
Step Thirty Two: Install the Remote Switch Box to the switch plate on the motor
using (4) 1/4”*3/4” hex bolts and (4) 1/4”*OD19*2t flat washers.
Step Thirty Three: Take the paddle and paddle branch and assemble together
using (4) 1/4”*5/8” hex bolts, (8) 1/4”*OD13*1t flat washers and (4) 1/4” hex nuts.
Step Thirty Four: Assemble the two paddle and paddle branch assemblies to the
rotation shaft using (4) 1/4”*5/8” hex bolts, (8) 1/4”*OD13*1t flat washers and (4)
1/4” hex nuts.
3HP Mobile Dust Cyclone Manual
30
Step Thirty Two: Install the Remote Switch Box to the switch plate on the motor
using (4) 1/4”*3/4” hex bolts and (4) 1/4”*OD19*2t flat washers.
Step Thirty Three: Take the paddle and paddle branch and assemble together
using (4) 1/4”*5/8” hex bolts, (8) 1/4”*OD13*1t flat washers and (4) 1/4” hex nuts.
Step Thirty Four: Assemble the two paddle and paddle branch assemblies to the
rotation shaft using (4) 1/4”*5/8” hex bolts, (8) 1/4”*OD13*1t flat washers and (4)
1/4” hex nuts.
Drum insert
