background image

                                                

 

 

 

 

 

 

 

 

 

 

 

Part number 21729, Rev 4                                                                                                      

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

ULTRA LOW TEMPERATURE FREEZER 

 

OWNER’S INSTRUCTIONS 

This manual describes how to operate and care for your appliance to get the best, most efficient 
performance. 

READ THIS BOOK! 

Note to Customer: 

This merchandise was carefully packed and thoroughly inspected before leaving our plant.  Responsibility 

for its safe delivery was assumed by the carrier upon acceptance of the shipment.  As directed on the side 

of your packing carton, claims for loss or damage sustained in transit must be made on the carrier as 

follows: 

 

A.)

 

Visible Loss, Damage, Shortage External Evidence of Loss or Damage: This type of damage 

must be noted on the freight bill and acknowledged by the carrier’s agent (driver) at time of delivery. 

Make sure you get a signed copy. Send a written request for an inspection to the carrier.  

B.)

 

Concealed Damage: This type of damage may not be discovered until the unit is being unpacked. 

When concealed damage is discovered, stop unpacking immediately and contact the carrier 

immediately to report the claim and request an inspection. This should be done as soon as possible 

and, in any case, must be done within 15 days or receiving the merchandise. If at all possible, do not 

move the item and save all packaging material for carrier’s inspection.  

C.)

 

FAILURE TO FOLLOW THESE INSTRUCTIONS MAY  RESULT IN THE CARRIER 

REFUSING TO HONOR YOUR COMPANY’S CLAIM. UNDER NO CIRCUMSTANCES 

SHOULD THE MERCHANDISE BE RETURNED TO THE MANUFACTURER. NO 

RETURNS WILL BE ACCEPTED WITHOUT PRIOR AUTHORIZATION. 

 

Summary of Contents for GM-ULT-1786























Reviews: