Labelmate.com
USE EXTREM CAUTION WHEN MANIPULATING THE BLADES
DO NOT ADJUST THE BLADES WHILE SLITTING
SET-UP
1. Set the unit in place near the printer.
2. Verify that the “RUN/STOP” switch is in the “STOP” position, and that the Torque Adjust Knob is turned all the way down.
3. Place an empty label core onto the QUICK-CHUCK of the SR Rewinder and press snugly in place against the inner Label
Flange Plate.
4. Slide one of the SP-76-220AL Aluminium Separator Plates onto the QUICK-CHUCK so that it rests against the label core.
Repeat this step for the number of Finish Rolls that you desire when done slitting/rewinding. Then place the Outer Guide
Flange onto the QUICK-CHUCK.
5 Turn the knob of the QUICK-CHUCK clockwise to expand the QUICK-CHUCK and affix the empty cores, Separator Plates,
and Outer Guide Flange firmly in place.
6. Unscrew knob J and lift Bar H. Rotate/Tilt back BH-1 ASSY Blades I and tighten knob K to maintain Blades in tilted back
position. This will enable you to thread the media through the SR.
7. Pre-cut approximately the first three feet of the lanes between the labels where you would like the BH-1 ASSY Blades
to cut.
8. Thread the material being printed onto the SR as shown in “Figure A”:
(a) Over Aluminium Roller A
(b) Underneath Tensioning Roller B
(c) Over and around the top of Plastic Roller C
(d) Between Aluminium Roller D and the steel rod underneath it
(e) Tape the leading edges of the pre-cut material onto the empty cores that are on the QUICK-CHUCK.
(f) Using the supplied Hexagonal Wrench, loosen the set-screw of Outer Guide Rings E and F and position them next
to the outer edge of the media being slit/rewound. Retighten the set-screws.
(
Note
: the Inner Guide Rings that are positioned against the black metal chassis of the Rewinder on Rod A, and
Rollers B and D require very little adjustment, if any, and should be aligned with the face of the Label Flange Plate.)
(g) Extend the Blades from the BH-1 ASSY Blades approximately 1.5” and position the Blades in the desired slitting
position by loosening screws L and sliding the blades along the aluminium shaft, and then tightening the screws
once the Blades are positioned as desired.
(h) Rotate knob K down until the BH-1 ASSY Blades made contact with white plastic Shaft C. Reposition Bar H and
Knob J as seen in “Figure A” and tighten Knob J (
be careful not to over-tighten
).
(i) Push down the material being printed between the printer and Roller A to form a tensionless loop of material as
seen in “Figure A”.
9. Plug the Power Plug at the end of the wire on the Power Supply Module into the Unit’s Power Input Jack. Plug the Power
Supply into an appropriate AC power outlet.
10. Flip the Master Power Rocker Switch on the rear of the SR to the “Power On” position.
11 Adjust the angle of Sensor G so that it points at the desired location on the tensionless loop of material. The angle of
the sensor determines the depth of the loop.
Note
: The Rewinder will continue to turn as long as the eye of the sensor can
“see” the material in the tensionless loop.)
13. Select the “HIGH” Torque Setting with the switch on the top of the unit.
14. Select the desired rewind direction with the switch on the top of the unit.
15. Flip the “RUN/STOP” switch to “RUN”.
16. Turn the black knob of Tensioning Roller B to adjust/achieve the desired tension of the material being rewound.
17. Gradually turn the Torque Adjust Knob until the desired rewind speed is achieved.
Getting started
Summary of Contents for SR6
