background image

EN

3

•   do not use extension cords in bath or 

shower rooms;

•   do  not  unplug  the  device  from  the 

power outlet by pulling on the power 

supply cable;

•   do  not  expose  the  device  to 

atmospheric agents (rain, sun, etc.);

•   do  not  allow  children  or  untrained 

people to use this device;

• do not clean the control panel with a wet 

cloth since it is not watertight.

13)

  Before  carrying  out  any  maintenance 

and/or cleaning operations, turn the main 

switch, which is located on the front left of 

the machine, to the “0” or “OFF” position, 

and  disconnect  the  machine  from  the 

electrical network by unplugging the cord 

or  by  switching  off  the  relative  circuit 

breaker. For any cleaning operation, follow 

exclusively  the  instructions  contained  in 

this manual.

14) 

In  case  the  machine  is  operating 

in  a  faulty  manner  or  breaks  down, 

disconnect  it  from  the  electrical  network 

(as  described  in  the  preceding  point) 

and close the water supply valve. Do not 

attempt  to  repair  it.    Contact  a  qualified 

and  authorized  professional  to  perform 

any repair.  Any repairs must be performed 

exclusively  by  the  manufacturer  or  by  an 

authorized centre using only original parts. 

Non  compliance  with  the  above  could 

compromise  the  safe  operation  of  the 

machine.

15) 

You  should  plan  to  make  use  of  an 

omnipolar  connector  during  installation, 

as  required  by  local,  national,  and 

international  electrical  codes  and 

regulations.

16) 

In order to avoid dangerous overheating 

problems,  it  is  recommended  that  the 

power supply cable be fully unfurled.

17) 

Do not obstruct air intake and exhaust 

grilles and, in particular, do not cover the 

cup warmer tray with cloths or other items.

18) 

The  machine’s  power  supply  cable 

must not be replaced by users.  In case the 

power  supply  cable  becomes  damaged, 

shut  off  the  machine  and  disconnect  the 

machine from the electctrical network by 

switching  off  the  relative  circuit  breaker  

and close off the water supply; to replace 

the  power  supply  cord,  contact  qualified 

professionals exclusively.

A

B

C

1) Common Dimensions, Weights, 

     and Features

WARNING

THE COFEE MACHINE MUST BE PLACED 

ON A COUNTER HIGHER THAN 80 CM 

FROM THE GROUND.

WARNING

THIS MACHINE IS NOT SUITABLE FOR 

OUTDOOR USE. JETS OF WATER SHOULD NOT 

BE USED TO CLEAN THE MACHINE, 

NOR SHOULD IT BE PLACED WHERE 

WATER JETS ARE USED.

WARNING

AS ALREADY MENTIONED IN THE PRECEDING 

NOTES, THE MANUFACTURER SHALL NOT BE 

HELD RESPONSIBLE FOR DAMAGE TO OB-

JECTS, ANIMALS AND/OR PEOPLE WHENEVER 

THE MACHINE HAS NOT BEEN INSTALLED AC-

CORDING TO THE INSTRUCTIONS CONTAINED 

IN THIS MANUAL, AND IS NOT USED TO DO 

WHAT IT WAS DESIGNED FOR (I.E. PREPARING 

COFFEE AND HOT DRINKS).

LINEA PB

2 gr.

A [mm]

B [mm]

C [mm]

WEIGHT [kg]

710

81

588

533

3 gr.

950

93

588

533

4 gr.

1190

117

588

533

Summary of Contents for V1.0

































































Reviews: