background image

4

La Marzocco, S.r.l.        Firenze, Scarperia, Italia

V1.0

Programming sequence

Barista Menu

• 

Coffee Boiler 1 Switching on/off

• 

Coffee Boiler 2 Switching on/off

• 

Coffee Boiler 3 Switching on/off

• 

Coffee Boiler 1 Temperature

• 

Coffee Boiler 2 Temperature

• 

Coffee Boiler 3 Temperature

• 

Steam Boiler Temperature

• 

Clock Adjust

Programming Sequence

• 

Language

• 

Temperature Measurement Units (°F - °C)

• 

User name

• 

Coffee Boiler 1 Temperature

• 

Coffee Boiler 2 Temperature

• 

Coffee Boiler 3 Temperature

• 

Steam Boiler Temperature

• 

Clock Adjust

• 

Auto On/Off

• 

Cup Heating

• 

Pumps Setting for Automatic Fill

• 

Steam Boiler Automatic Fill

• 

Pump Setting for Tea Water

• 

Coffee Boiler 1 Temperature Offset

• 

Coffee Boiler 2 Temperature Offset

• 

Coffee Boiler 3 Temperature Offset

• 

Total Doses

• 

Filter Alarm

Operating Procedure:

 with the coffee machine 

on

, press and 

hold the jog wheel for 5 seconds and the Barista Level 

menu will appear. 

Operating Procedure:

 First hold the knob for 3 seconds to 

achieve the OFF status, then realease it and

 

 press and 

hold it again for an additional 5 seconds. The Technician 

Level menu will appear. 

Description of the Levels

Technical Menu

Summary of Contents for strada ep























Reviews: