background image

Propane Vapor

Withdrawal

or

Natural Gas

Congratulations!

You have purchased the finest circulating construction heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced

manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and welcome 

any suggestions or comments you may have...call us, toll-free, at 1-800-345-7200.

Owner's Manual and Instructions

Dual Fuel Construction Heater

View this manual online at www.lbwhite.com

150-29447

MODELS

OUTPUT (kW)

FUEL

TS350                  

102.6

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International in accordance

with the requirements of Standard ANSI Z83.7 

CSA 2.14 and is listed and

approved as a ductable direct gas-fired forced-air construction heater with

application for the temporary heating of buildings under construction, alteration, or

repair.  If you are considering using this product for any application other than its

intended use, then please contact your fuel gas supplier, or the L.B. White Co., Inc.

Certification by:

SCAN THIS QR CODE

with your smartphone or 
visit http://goo.gl/nvneR
to view maintenance
videos for L.B.White heaters.*

*Requires an app like QR Droid for Android or 
QR Reader for iPhone.

Summary of Contents for Premier TS350


































Reviews: