background image

Direct

Spark

Congratulations!

You have purchased the finest heater available. 

Your new L.B. White heater incorporates the benefits from the most experienced
manufacturer of heating products using state-of-the-art technology.

We, at L.B. White, 

thank you

for your confidence in our products and welcome 

any suggestions or comments you may have...call us, toll-free, at (800) 345-7200.

Owner's Manual and Instructions

Certification by:

MODEL

IGNITION

OUTPUT 

(Btuh)

FUEL

PALS

ATTENTION ALL USERS

This heater has been tested and evaluated by C.S.A. International in accordance
with Standard ANSI Z83.7

z

CSA 2.14 and is listed and approved as a direct gas-

fired convection construction heater with intended use for primarily the
temporary heating of buildings under construction, alteration, or repair.  As an
alternative use, this heater has also been tested and evaluated by the L.B. White
Co., Inc. for the heating of PALS agricultural animal confinement buildings.  This
heater iis ddesigned ffor iindoor hhanging iinstallation oonly.  IIt sshall bbe iinstalled
according tto m

minimum cclearances aas pprescribed iin tthis oowner’s m

manual aand oon

the hheater’s ddataplate.  If you are considering using this product for any
applications other than those previously stated, then please contact your fuel gas
supplier or the L.B. White Co., Inc.

Propane Vapor

Natural Gas

250,000

200,000

150-22668-B

Summary of Contents for PALS

























Reviews: