background image

Guardian Brood Heaters

Owner’s Manual • Guardian

7

Ŷ/3*KDVDGLVWLQFWLYHRGRU/HDUQWRUHFRJQL]H

these odors. (Reference Fuel Gas Odor and Odor 
Fading sections above.

Ŷ,I\RXKDYHQRWEHHQSURSHUO\WUDLQHGLQUHSDLUDQG

service of LPG and natural gas brood heaters, then 
do not attempt to light the heater, perform service 
or repairs, or make any adjustments to the brood 
heater on the fuel system.

Even if you are not properly trained in the service and 
repair of the brood heater, ALWAYS be consciously 
aware of the odors of LPG and natural gas.

Ŷ$SHULRGLFVQLIIWHVWDURXQGWKHEURRGKHDWHURUDW

the brood heater’s joints; i.e. hose, connections, 
etc., is a good safety practice under any conditions. 
If you smell even a small amount of gas, CONTACT 
YOUR FUEL GAS SUPPLIER IMMEDIATELY. DO 
NOT WAIT!

1.  Do not attempt to install, repair, or service this 

brood heater or the gas supply line unless you 
have continuing expert training and knowledge of 
gas heaters.

4XDOL¿FDWLRQVIRUVHUYLFHDQGLQVWDOOD

-

tion of this equipment are as follows:

D7REHDTXDOL¿HGJDVEURRGKHDWHUVHUYLFHSHUVRQ

\RXPXVWKDYHVXI¿FLHQWWUDLQLQJDQGH[SHULHQFH
WRKDQGOHDOODVSHFWVRIJDV¿UHGEURRGKHDWHU

installation, service and repair. This includes the 
task of installation, troubleshooting, replacement 
of defective parts and testing of the brood heater. 
You must be able to place the brood heater into a 
continuing safe and normal operating condition. 
You must completely familiarize yourself with each 
model brood heater by reading and complying with 
the safety instructions, labels, Owner’s Manual, 
etc., that is provided with each heater.

E7REHDTXDOL¿HGJDVLQVWDOODWLRQSHUVRQ\RXPXVW

KDYHVXI¿FLHQWWUDLQLQJDQGH[SHULHQFHWRKDQGOH

all aspects of installing, repairing and altering gas 
lines, including selecting and installing the proper 
equipment, and selecting proper pipe and tank size 
to be used. This must be done in accordance with 
all local, state and national codes as well as the 
manufacturer’s requirements.

2.  All installations and applications of L.B. White 

brood heaters must meet all relevant local, state 
and national codes. Included are LPG, natural gas, 
electrical, and safety codes. Your local fuel gas 

VXSSOLHUDORFDOOLFHQVHGHOHFWULFLDQWKHORFDO¿UH

department or similar government agencies, or 
your insurance agent can help you determine code 
requirements.

3.  Do not move, handle, or service the brood heater 

while in operation or connected to a power or fuel 
supply.

4.  This brood heater may be installed in areas 

subject to washdown. This brood heater may only 
be washed on the external case assembly—see 
Cleaning Instructions. Do not wash the interior 
of the brood heater. Use only compressed air, 
soft brush or dry cloth to clean the interior of the 
brood heater and it’s components. After external 
washdown, do not operate this brood heater until 
it is completely dry. In any event, do not operate 
the brood heater for at least one hour after external 
washdown.

5.  For safety, this brood heater is equipped with a 

manual reset high-limit switch and an air proving 
switch. Never operate this brood heater with any 
safety device that has been bypassed. Do not op-
erate this brood heater unless all of these features 
are fully functioning.

6.  Do not operate the brood heater with its door open 

or panel removed.

7.  Do not locate fuel gas containers or fuel supply 

hoses anywhere near the blower outlet of the 
brood heater.

8.  Do not block air intakes or discharge outlets of the 

brood heater. Doing so may cause improper com-
bustion or damage to brood heater components 
leading to property damage or animal loss.

9.  The hose assembly shall be visually inspected on 

an annual basis. If it is evident there is excessive 
abrasion or wear, or if the hose is cut, it must be 
replaced prior to the brood heater being put into 
operation. The hose assembly shall be protected 
from animals, building materials, and contact with 
hot surfaces during use. The replacement hose  

DVVHPEO\VKDOOEHWKDWVSHFL¿HGE\WKHPDQXIDF

-

turer. See parts list.

Attention - Critical 

Points to Remember!

Summary of Contents for AD060

















































































Reviews: