background image

WARNING

This heater must not be washed.  Use of a pressure

washer, water or liquid cleaning solution on this heater

can cause severe personal injury or property damage due

to water and/or cleaning solution:

A. In electrical components, connections and wires

causing electrical shock or component failure.

B. On gas control components causing corrosion which

can result in gas leaks and fire or explosion from the

leak.

The heater must be cleaning in accordance with the

manufacturer’s instructions without being subjected to

liquid spray or wetting.

1. Have your gas supplier check all gas piping annually

for leaks or restrictions in gas lines.  Also, at this time

have your gas supplier clean out the sediment trap of

any debris that may have accumulated.  

2. The aappliance aarea sshall bbe kkept cclear aand ffree ffrom

combustible m

materials, ggasoline, aand oother fflammable

vapors aand lliquids.

3. Regulators can wear out and function improperly.

Have your gas supplier check the date codes on all

regulators installed and check delivery pressures to

the appliance to make sure that the regulator is

reliable.

4. Regulators must be periodically inspected to make

sure the regulator vents are not blocked.  Debris,

insects, insect nests, snow, or ice on a regulator can

block vents and cause excess pressure at the

appliance.

1. Before cleaning, shut off all gas supply valves and

disconnect electrical supply.

2. The heater should have dirt or dust removed

periodically:

a. After each use, give the heater a general cleaning

using compressed air or a soft brush on its interior

and exterior.  At this time, dust off the motor case

to prevent the motor from over-heating and

shutting the heater down.

b. At least once a year, give the heater a thorough

cleaning.  At this time, remove the fan and motor

assembly and brush or blow off the fan wheel,

giving attention to the individual fan blades.

Additionally, make sure the burner air inlet venturi

ports and the “throat” of the casting are free of

dust accumulation and the area between the heat

chamber top and inside case is also free of dust. 

c. Observe and obey the Warning within these

Cleaning Instructions.  This same Warning is also

supplied on the heater. 

15

Cleaning Instructions

Maintenance Instructions

WARNING

Fire, B

Burn, aand EExplosion H

Hazard

This heater contains electrical and mechanical components in the gas management, safety and airflow systems.

Such components may become inoperative or fail due to dust, dirt, wear, aging, or the corrosive atmosphere of an

animal confinement building.

Periodic cleaning and inspection as well as proper maintenance are essential to avoid serious injury or property

damage.

Summary of Contents for 346JX



























Reviews: