L-Acoustics KS21i Owner'S Manual Download Page 75

Page: 75 / 119

Rigging procedures

Assembly

Procedure

Fasteners for wall-mounting or ceiling-mounting

Select screw length and anchors applicable to the wall or ceiling properties.

Mount A-U15i on the ceiling or on the wall using four M10 screws.

When using a U-bracket horizontally, make sure the hooks are oriented upwards.

781 mm / 30.7 in

120 mm / 4.7 in

Ø M10 (x4)

Remove the placeholder screws at the center of each side of the enclosure:

KS21i

A15i Wide/Focus

Remove the two screws.

Remove the central and top screws or the central

and bottom screws, depending on the desired

conguration (refer to

APPENDIX B: Congurations

with A-U15i

(p.113)).

Using the screws provided with A-U15i, drive a screw on both sides.
Approximately 10 mm (0.4 in) of the thread must be visible.

10 mm / 0.4 in

KS21i

A15i Wide/Focus

Alternatively, drive the screw in the bottom insert for a conguration with the enclosure closer to the ceiling.

A15i owner's manual (EN) version 1.0

Summary of Contents for KS21i
























































































































Search results

Summary of Contents for KS21i

Reviews:

Related manuals for KS21i

Brands by name

Popular brands

L-Acoustics KS21i, Owner'S Manual

Search results

Summary of Contents for KS21i

Reviews:

Related manuals for KS21i

Brands by name

Popular brands