L-Acoustics KS21i Owner'S Manual Download Page 74

Page: 74 / 119

Rigging procedures

Wall-mounting or ceiling-mounting

Mounting an assembly with A-U15i

Type of deployment

ceiling-mounting, wall-mounting

Rigging accessories

A-U15i
U-bracket rigging plates

Additional accessories

M8x35 rigging screws (provided)
4 x M10 screws and anchors
T40 Torx bits

Min number of operators

Rigging plates

A15i-ULINK

Rigging plates

for ying two

A15i with A-U15i

A15iKS21i-ULINK

Rigging plates for

ying A15i under

KS21i with A-U15i

KS21i-ULINK

Rigging plates

for ying

two KS21i

with A-U15i

Additional safety for own arrays

When ying an array, use available holes to implement a secondary safety.

The procedure is shown with A-U15i in horizontal position.

The same procedure applies for all congurations with A-U15i. Refer to

APPENDIX B: Congurations with A-U15i

(p.113).

Resistance value of anchoring points

Conguration

Tensile load

Shear load

A-U15i in horizontal position, with 1 enclosure

275 daN

65 daN

A-U15i in horizontal position, with 2 enclosures

375 daN

75 daN

Wall-mounted

A-U15i in vertical position, with 1 enclosure

40 daN

30 daN

Ceiling-mounted

150 daN

—

A15i owner's manual (EN) version 1.0

Summary of Contents for KS21i
























































































































Search results

Summary of Contents for KS21i

Reviews:

Related manuals for KS21i

Brands by name

Popular brands

L-Acoustics KS21i, Owner'S Manual

Search results

Summary of Contents for KS21i

Reviews:

Related manuals for KS21i

Brands by name

Popular brands