background image

Loudspeaker congurations

A15 Wide/Focus line source element with low-frequency element

With a complementary subwoofer, the system is extended in the low end and the LF contour is reinforced.
The [A15_FI] preset delivers a reference frequency response in short throw applications. The [KS21_60] preset provides

KS21 with an upper frequency limit at 60 Hz.
The A15 Wide/Focus and KS21 enclosures are driven by the  LA4X / LA8 / LA12X  amplied controllers.

Enclosure

A15 Wide/Focus

KS21

Preset

[A15_FI]

[KS21_60]

Recommended ratio

1 A15 Wide/Focus : 1 KS21

Frequency range (-10 dB)

29 Hz - 20 kHz

Use [xxxx_xx_C] on a reversed subwoofer in a cardioid conguration

The cardioid conguration consists in reversing 1 element in an array of 4 subwoofers.
Refer to the subwoofer owner's manual and to the 

Cardioid congurations

 technical bulletin.

Grouping subwoofers

Place the subwoofer enclosures side by side. If not possible, the maximum distance between two adjacent

acoustic centers must be 2.8 m or 1.7 m if the upper frequency limit of the subwoofer system is at 60 Hz or

100 Hz, respectively.

Delay values

Do not forget to add the pre-alignment and geometric delays depending on the conguration.

pre-alignment delays

[A15] or [A15_FI] + [KS21_60]

A15 Wide/Focus = 0 ms

KS21 = 2.6 ms

[A15] or [A15_FI] + [KS21_60_C]

A15 Wide/Focus = 3.1 ms

KS21 = 0 ms

48 

 A15 owner's manual (EN) version 1.2

Summary of Contents for A15 Focus



































































































Reviews: