L-Acoustics A15 Focus Owner'S Manual Download

Page: 32 / 98

Rigging system description

Rigging elements for stacked arrays

A-TILT

A-TILT is a site angle adjustment accessory that interfaces between KS21 and A15 Wide/Focus in a stacked array. It is

used in combination with two KS21-OUTRIG

under KS21 to ensure stability.

Alternatively, mount the KS21 array on KS21-CHARIOT and use K2-JACK to stabilize the array.

Refer to

Attaching K2-JACK stabilizers to KS21-CHARIOT

(p.73).

Do not use A-TILT in a own array.

The studs on A-TILT match the lodgings on the enclosure, to enable deployments with the HF section on either side. A-TILT

is secured to the enclosure and to the subwoofer with threaded knobs.

A-TILT-compatible subwoofers

The A-TILT subwoofer knob can only be secured in pole-mount sockets that contain an M20 insert.

⌀

M20

subwoofer knob

studs

enclosure knob

angle pin (x2)

subwoofer knob

enclosure knob

position in use

storage position

A15 owner's manual (EN) version 1.2

Summary of Contents for A15 Focus



































































































Search results

Summary of Contents for A15 Focus

Reviews:

Related manuals for A15 Focus

Brands by name

Popular brands

L-Acoustics A15 Focus, Owner'S Manual

Search results

Summary of Contents for A15 Focus

Reviews:

Related manuals for A15 Focus

Brands by name

Popular brands