KYOWA DPM-900 Series Instruction Manual Download Page 36 | Manualshive

Page: 36 / 64

background image

31

5-15 TPN/DLT MEASURING MODE

（

For the DPM-911/951 only

）

In addition the strain gages or strain gage transducers, the DPM-900/950 series can measure data using
Rotary Transformer Torque Transducer, and Inductance-Type Displacement Transducer.

Be sure to change modes to the TPN/DLT Measuring Mode for using the Rotary Transformer
Torque Transducer or Inductance-Type Displacement Transducer.

To change modes to the TPN/DLT Measuring Mode, turn ON the Setting Switch 4 on the rear panel. Be
sure to turn OFF the DPM-900/950 series before changing the Setting Switches.
In addition, for how to set the internal gain, read 5-7 INTERNAL GAIN.

Turn ON the “Setting Switch 4” and immediately after turning ON the power, check that the monitor
display changes as follows.
All LED light up ® Version of the built-in software ® ‘

’

（

Scroll horizontally

）

® Output voltage
The

appears in the TPN/DLT Measuring Mode only.

Do not conduct the bridge check function with the Rotary Transformer Torque Transducer
connected.
If the “Setting Switch 4” of the DPM-912/913/952 is turned ON, the DPM-912/913/952 is still in
the Normal Mode.

NOTE

After turning ON the DPM-900/950 series, press and hold the

SET

switch for checking the TPN/DLT

Measuring Mode.
The following display appears on the monitor.

The version of the built-in software and are scrolled horizontally.

Press and hold the

SET

switch if the Setting Switch 4 is set to OFF.

The following display appears.

The version of the built-in software is scrolled horizontally.

MEMO

«
...
34
35
36
37
38
...
»

Summary of Contents for DPM-900 Series

































































Reviews:

No comments

Related manuals for DPM-900 Series

Brand: Quest Engineering Pages: 19

Brand: Harman Kardon Pages: 12

Brand: Harman Kardon Pages: 7

Brand: Harman Kardon Pages: 3

Brand: Unika Pages: 15

Richer Bass RB1

Brand: Laney Pages: 8

Brand: Laney Pages: 16

Brand: Laney Pages: 6

Brand: S.M.S.L Pages: 32

Brand: Atlona Pages: 9

Brand: Flight Display Systems Pages: 15

Brand: PS Audio Pages: 28

Brand: Akai Pages: 21

Wireless2100-System

Brand: MultiChannel Pages: 43

Brand: Baja Pages: 20

Acoustic Box II

Brand: Vintage Revolution Pages: 17

Brand: Signal Vehicle Products Pages: 20

Brand: Rane Pages: 19

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands