manualshive.com logo in svg

KYMCO K-XCT 300i, Owner'S Manual, Page: 649 / 656

Share
Download
KYMCO K-XCT 300i Owner'S Manual Download Page 649

 
 
14. Troubleshooting                                                                                                      K- XCT 300i

 

 

 

14

‐

23

 

 

 

Troubleshooting 

 

 

Vehicle can not be started 

 

Preliminary 6 Step Inspection 

 

 

  1. Is the battery fully charged (12V or higher). See the Battery topic for more 

information. 

 
    2. Key-On and listen for any action with Fuel Pump / Fuel Pump Relay (It will turn 

off automatically in 5-10 seconds) 

 
  3. Key-On to check for any failure lamp light up on dashboard. See the Self-

Diagnosis topic for more information. 

 
 
    4. Is the Idle screw of Throttle Valve being changed or loosed? 
 
    5. Has the vehicle under regular service? Is the gas station a good one? 
 
    6. Is the spark plug the correct model of specified by the vehicle builder?   

 
 
 
 

Troubleshooting by section 

 

 

•  Brakes 
•  Cooling System 
•  CVT 

Continuously Variable Transmission 

•  Electrical Systems 
•  Engine 
•  Final 

Drive 

•  Front 

Suspension 

•  Fuel 

Injection System 

•  Rear Suspension 
•  Steering 
•  Wheels 

 

 

 
 
 
 
 

Summary of Contents for K-XCT 300i

















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments