manualshive.com logo in svg

KYMCO K-XCT 300i, Owner'S Manual, Page: 374 / 656

Share
Download
KYMCO K-XCT 300i Owner'S Manual Download Page 374

 
 
7. Fuel System> Fuel Pump                                             K- XCT 300i 

 
 

7-14 

 

 

 

 

 

Set the engine stop switch to the “RUN” position. 

 

 

Unplug the fuel pump connecter. 

 

Set the multi meter to read battery voltage. 

 

Touch the  multi  meter  leads to  the  harness side of  the  fuel  pump 
connector,  with  the positive  lead  touching  the red/black wire  terminal 
and the negative lead touching the green wire terminal. 

 

Turn  the  ignition  switch  on.  The  battery  voltage  should  show  for  a  few 
seconds.  Replace  the  fuel  pump  if  it  is  not  functioning  and  the  input 
voltage is correct. 

 

If the battery voltage is not present check the following: 

 

● Fuse B (10 A) 

● Fuel cut-off relay 

● ECU 

 

Summary of Contents for K-XCT 300i

















































































































































































































































































































































































































































































































































































































































































Reviews:

No comments