KYLAND Technology PTS-DR200 Operation Manual Download

Page: 44 / 55

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 42 -

Items

Parameters

Description

Range is between 0 and 7.
Default value is 7.

vLan CFI

0~1

Set vLan CFI information of GOOSE message.
Range is between 0 and 1.
Default value is 0.

vLan ID

0~4095

Set vLan ID information of GOOSE message.
Range is between 0 and 4095.
Default value is 0.

Test

0~1

Set Test flag of GOOSE message.
Range is between 0 and 1.
Default value is 0.

confRev

0~255

Set confRev value of GOOSE message.
Range is between 0 and 255.
Default value is 1.

ndsCom

0~255

Set ndsCom value of GOOSE message.
Range is between 0 and 255.
Default value is 0.

Press ‘Save’ button to save the current setting when you change setting.

If select ‘GOOSE-S0’ in GOOSE Channel, the setting screen will be shown as:

[Figure 3-26] GOOSE Subscriber Screen (GOOSE-S0)

Table 25 –GOOSE Subscriber Setting (GOOSE-S0)

Items

Parameters

Description

GOOSE Subscriber

Enable

Activate GOOSE subscriber feature for ETH0.

Summary of Contents for PTS-DR200
























































Search results

Summary of Contents for PTS-DR200

Reviews:

Related manuals for PTS-DR200

Brands by name

Popular brands

KYLAND Technology PTS-DR200, Operation Manual

Search results

Summary of Contents for PTS-DR200

Reviews:

Related manuals for PTS-DR200

Brands by name

Popular brands