KYLAND Technology PTS-DR200 Operation Manual Download | Manualshive

Page: 15 / 55

background image

Kyland Technology (Shanghai) Co., Ltd PTS-DR200 Time Server

- 13 -

Select ‘IRIG-B1’ in Source Channel, the screen will be shown as:

[Figure 3-6] Source Status Screen (IRIG-B1)

Table 6 – Source Status Information (IRIG-B1)

Items

Parameters

Description

Source Status

Normal

Alarm

Show the time source status.
Normal: The time source can use;
Alarm: The time source cannot use.

Source Bump

Status

Normal

Alarm

Show the time source bump status.
Normal: The time source has not bump data.
Alarm: The time source has bump data.

Source Priority

1~10

Show the priority for time source. 1 is highest source and 10 is
lowest source. It has 10 levels. System can select best time
sources by source priority.

Select ‘IRIG-B2’ in Source Channel, the screen will be shown as:

[Figure 3-7] Source Status Screen (IRIG-B2)

Table 7 – Source Status Information (IRIG-B2)

Items

Parameters

Description

Source Status

Normal

Alarm

Show the time source status.
Normal: The time source can use;
Alarm: The time source cannot use.

Source Bump

Normal

Show the time source bump status.

«
...
13
14
15
16
17
...
»

Summary of Contents for PTS-DR200
























































Reviews:

No comments

Related manuals for PTS-DR200

DSN-4100 Series

Brand: D-Link Pages: 2

Brand: D-Link Pages: 2

Brand: IBM Pages: 32

Network Adapter AC AAP

Brand: Extron electronics Pages: 2

Conettix ITS-D6686-INTL

Brand: Bosch Pages: 10

Brand: Bosch Pages: 12

Conettix ITS-D6686-UL

Brand: Bosch Pages: 12

Brand: Bosch Pages: 8

Brand: Bosch Pages: 20

Brand: Bosch Pages: 20

Brand: Bosch Pages: 86

Brand: Bosch Pages: 80

Dual E3 Asynchronous

Brand: 3Com Pages: 22

Brand: Pentagram Pages: 20

Brand: AirLive Pages: 46

Brand: Hangzhou Gubei Electronics Pages: 10

Brand: SMC Networks Pages: 7

TotalStorage FAStT700

Brand: IBM Pages: 100

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands