background image

KIEN1005G  User’s  Manual  201106 

Notice for Safety Operation 

 

This product performs reliably as long as it is used according to the guidance. Artificial damage 

or destruction of the equipment should be avoided.     

z

 

Read this manual carefully and keep it for future reference;     

z

 

Do not place the equipment near water sources or damp areas; 

z

 

Do not place anything on power cable and put the cable in unreachable places; 

z

 

Do not tie or wrap the cable to prevent fire. 

z

 

Power  connectors  and  other  equipment  connectors  should  be  firmly  interconnected       

and checked frequently. 

z

 

Do not repair the equipment by yourself, unless it is clearly specified in the manual. 

z

 

Please keep the equipment clean; if necessary, wipe the equipment with soft cotton cloth. 

In the following cases, please immediately cut off the power supply and contact our company: 

¾

 

Water gets into the equipment; 

¾

 

Equipment damage or shell breakage; 

¾

 

Abnormal operation of equipment or its performances have completely changed; 

¾

 

The equipment emits odor, smoke or abnormal noise. 

 

 

Summary of Contents for KIEN1005G

















Reviews: