background image

 

2. Basic set up 

 

Arm base: 

Mount the arm base on the turntable at a distance of 212 mm from spindle!   If the pre-cut arm board 
has a thread ( M5), then use three screws and fix them from the top through the arm base into the arm 
board  thread,  or  use  a  ring  underneath  and  fix  three  screws  into  this  ring,  which  will then  hold  the 
arm base very tightly.  Ensure that you position the arm base so as to give access to an Allen key for 
fixing the arm tower into the arm base i.e. towards the rear right back corner of the turntable.  Also 
check,  when  mounting  the  arm  on  other  turntables,  that  you  allow  enough  clearance  for  the 
counterweight and correct position of the tube in relationship to the platter. ( Fig. 3&4) 
Due to the special bearing construction, there is only a limited arc in which the arm tube can travel in 
a horizontal way.  

      

 

Fig. 3. Kuzma arm base                                    Fig. 4. Arm base on arm board 
  
        

Arm tower:  

Insert  the  arm  tower  into  the  arm  base.    Ensure  that  the  height  is  such,  that  the  top  surface  of  the 
platform holding the cueing device is at a similar height to the record.  Fix it with an Allen key in the 
arm base.  Also check that the VTA  screw is allows you to keep the tower at the chosen  height. 
 ( Fig. 5&5a) 
 

      

                                 

 

Fig. 5. Arm tower- various adjustments                       Fig. 5a. Arm tower locking in arm base 
   
 

Summary of Contents for 4POINT 9




















Reviews: