background image

36 

Examples of cooking power setting 

(the values below are indicative) 

1 to 2 

Melting 
Reheating 

Sauces, butter, chocolate, gelatine 
Dishes prepared beforehand 

2 to 3 

Simmering 
Defrosting 

Rice, pudding, sugar syrup 
Dried vegetables, fish, frozen products 

3 to 4 

Steam 

Vegetables, fish, meat 

4 to 5 

Water 

Steamed potatoes, soups, pasta,  
fresh vegetables 

6 to 7 

Medium cooking 
Simmering 

Meat, lever, eggs, sausages 
Goulash, roulade, tripe 

7 to 8 

Cooking 

Potatoes, fritters, wafers 

Frying, roosting, boiling water  Steaks, omelettes, fried dishes, water 

Frying, roosting 
Boiling water 

scallops, steaks 
Boiling significant quantities of water 

 

MAINTENANCE AND CLEANING 

Switch-off the appliance before cleaning. 
Do not clean the hob if the glass is too hot because they are risk of burn. 

  Remove  light  marks  with  a  damp  cloth  with  washing  up  liquid  diluted  in  a  little  water. 

Then rinse with cold water and dry the surface thoroughly. 

  Highly  corrosive  or  abrasive  detergents  and  cleaning  equipment  likely  to  cause 

scratches must be absolutely avoided. 

  Do not ever use any steam-cleaner or pressure washer.  

  Do not use any object that may scratch the ceramic glass. 

  Ensure that the pan is dry and clean. Ensure that there are no grains of dust on your 

ceramic hob or on the pan. Sliding rough saucepans will scratch the surface. 

  Spillages of sugar, jam, jelly, etc. must be removed immediately. You will thus prevent 

the surface being damaged. 

 

WHAT TO DO IN CASE OF A PROBLEM 

The hob or the cooking zone doesn’t start-up : 

  The hob is badly connected on the electrical network. 

  The protection fuse cut-off. 

  The locking function is activated. 

  The sensitive keys are covered with grease or water. 

  An object is put on a key. 

The control panel displays [ U ] : 

  There is no pan on the cooking zone. 

  The pan is not compatible with induction. 

  The bottom diameter of the pan is too small. 

Continuous ventilation after cutting off the hob : 

  This is not a failure, the fan continuous to protect the electronic device. 

  The fan cooling stops automatically. 

Summary of Contents for EKI9652.1F





















Reviews: