manualshive.com logo in svg

Kuppersbusch IKD 10700.0, Service Manual

Share
Download
Kuppersbusch IKD 10700.0 Service Manual Download Page 10

10

H5-60-69-01

For internal use only

4.

Accessing the components

4.1

IKD ..., IKDEM ..., IKDUM ...

4.1.1

Operating element

In order to remove the operating element, remove the grease filter (see “6. Grease filter” on page 16).

Remove the two screws by inserting a mandrel into the round opening on the side of the screws.

[

Do not use flat pliers to loosen the screws! The casing and the screws may be scratched!

Once the screws have been loosened, the operating element can be removed towards the back, above
the grease filter.

To replace it, use the mounting aid, spare-part no. 340287 (2x). 

Please proceed as follows:

-

Insert the two threaded rods from the outside through the drilled holes of the operating element onto
the casing and screw onto the operation element. Then, by means of pulling up the two threaded
rods, guide the operation element to where it is to be mounted.

-

Screw out a threaded rod and screw in one of the screws which had previously been removed. Then
screw in the other screw. The screws should once again be tightened with a mandrel.

Summary of Contents for IKD 10700.0
























Reviews:

No comments

Brands by name

Popular brands

Load more brands