28
EEB 6450.0
Replacing the door seal
[
Do not use the oven if the door seal is damaged or missing!
If the seal is damaged, you will no longer be able to clean it. It must be re-
placed. New seals are available from KÜPPERSBUSCH Customer service.
Unhooking the seal
– To remove the seal, start by carefully
unhooking it at each corner.
Fitting a new seal
– Insert the new seal one corner at a
time into the oven front.
Take care not to bend the hooks out
of shape!
Model identification plate
Should you need to contact Customer Service or order spare parts, always
quote the information printed on the model identification plate.
The oven's identification plate is located just in-
side the oven on the right hand side and is vis-
ible when the door is open.
– Make a note of this information before you
consult Customer service.
Installation instructions for fitter
■
Only KÜPPERSBUSCH built-in hobs were designed and tested for use above
a Küpperbusch fitted oven. No other hobs may be used.
■
Statutory regulations and the connection specifications issued by the local
power apply company must be strictly observed.
■
Switch off the appliance by means of these safety devices before connecting
up the oven, carrying out repair work or replacing the oven light bulb.
Disconnect the appliance from the mains, disconnect fuse.
■
It must not be possible to touch components which are insulated under
operating conditions.
■
The earth wire must be so long that if the mains lead cleat fails, the live
wires of the connecting cable are subjected to tension before the earth wire.
■
The unit is ready to plug in and may be connected only to a properly
installed protected socket. Installing and wiring a socket or replacing the
connection cable should only be performed by an electrician and in
observance of the relevant regulations.
■
If the socket is inaccessible after the installation, safety regulations require
that an all-polo isolator with a contact opening of at least 3 mm be used
on the installation side.
■
The socket for plugging in the unit must be outside the installation space.
■
Built-in kitchen fixtures must be temperature resistant to 100 °C. This
applies especially to veneers, plastic coatings, adhesives and varnishes.
Adjacent cabinetry front must be temperature resistant to at least 70 °C.
■
The unit must be installed absolutely horizontal on a level, solid base. The
base must not be allowed to sag.
■
If the cupboard element is not attached to the way, screw on using an
ordinary bracket.
Electrics
[
WARNING! This appliance must be earthed!
Electrical requirements (for UK and Republic of Ireland only)
Check that the voltage stamped on the rating plate corresponds with your
house electricity supply, which must be AC (alternating current).
Electrical connection of the apppliance must be performed by a trained
electrician. The legally recognized regulations and the connection requirements
of the electricity board seving your area must be fully complied with.
[
WARNING! Should the oven be supplied with a continental two-pin plug
fitted, then this plug must be cut off from the connection cable. Dispose
of the plug safely; do not insert it in a 13 A socket elsewhere in the house
as this could cause a shock hazard.
Connection for UK and Republic of Ireland only: Permanent connection
to an oven power point (fuse: 20 A!).
Other countries:
Connection
is via the mains plug into a wall socket.
Total rating
at 230 V: 2.4 kW,
at 235 V: 2.5 kW
Electrical connection
230 - 240 V, 50 Hz
Fuse current
16 A
Installation dimensions
Installation in a fitted kitchen
Installing the appliance
(not correct for UK and
Republic of Ireland!)
– Plug into the wall socket.
(UK and Republic of Ireland:
Connect to an oven power
point!)
– Push the oven right into the
cupboard alcove. Do not jam
the cooker connection!
Fastening the appliance
– Open the oven door and fix the screws
supplied at an angle through the
cupboard.
Oven production number
Oven model type