background image

DE

DE

29

INTRODUCTION

About the manual

The manual ensures the safe operation of the devices and must be kept in the devices‘ close 

proximity, immediately accessible for any personnel.

All personnel are to carefully read and understand this manual before taking up work. As a 

precondition for safe operation, all safety instructions and operational procedures given in 

this manual must be observed.

Furthermore, the local accident prevention regulations and general safety provisions 

applicable for the devices‘ range of use are to be heeded.

Explanation of symbols

Safety instructions in this manual are indicated by means of symbols. The safety instructions 

express the extent of the hazard.

WARNING

This combination of symbol and signal word identifi es a possibly dangerous situation, 

which may cause death or severe injuries if not avoided.

CAUTION

This combination of symbol and signal word identifi es a possibly dangerous situation, 

which may cause minor or slight injuries if not avoided.

NOTE

This combination of symbol and signal word identifi es a possibly dangerous situation, 

which may cause damage to property and environment if not avoided.

TIP

 This symbol highlights useful tips and information for an effi  cient and trouble-free 

operation of the device.

Summary of Contents for PushBuddy




























Reviews: