background image

31

EN

EN

31 

PREPARATION

Delivery

TIP

Claims for damage can only be submitted within the applicable complaint periods, 

so please inform us of any defects as soon as possible.

The delivery is to be inspected for completeness and possible transport damage immediately 

upon receipt. Report transport damages to the carrier immediately.
The standard scope of delivery of the PushBuddy

®

 includes:

• 

PushBuddy

®

•  Carrier for transportation and securing the PushBuddy

®

 onto a Profi 3+ or a Profi HD

•  2x Extension 1,0 m

•  Extension 0,5 m

•  Torque wrench

•  Holding tool

•  Instruction manual

Packaging

TIP

 Keep the packaging for possible shipping and storage

Packaging may also comprise materials added to the packages for the protection against 

moisture or frost (e.g. silica gel bags, anti-freezing agents).

Storage

The devices and the accessories must always be stored under the following conditions:

•  Do not store outdoors

•  Store in a dry and dust-free place

Transport

When transporting the device in vehicles, always comply with the local safety loads regula-

tions. In addition, make sure that the PushBuddy

®

 and its accessories are protected against 

external forces.
A carrier can be used to transport the PushBuddy

®

 and its accessories to the place of opera-

tion. See chapter „Transport to place of operation“.

Summary of Contents for PushBuddy




























Reviews: