KUHN SpeedRake SR108 Operator'S Manual Download Page 41

Page: 41 / 44

Maintenance and storage

SpeedRake

SR108 SR110 SR112

3. Storage



At the end of each season

- Clean the machine thoroughly.

- Put the machine under cover in a dry place.

- Retract all hydraulic cylinders and coat the exposed

parts of ram rods with lubricant.

- Replace any damaged or missing safety decals.

- Replace all parts that are worn or damaged with KUHN

original parts.



At the start of each season

- Re-read the operators' manual.

- Check tire pressure. Refer to the technical

specifications' chart.

- Make sure all the guards are in place.

- Lubricate all grease points.

- Torque the transport wheel lug nuts to 120 ft lbs (163

daNm).

- Check tightness of all bolts and nuts on rake assembly,

particularly on rake wheels.

Summary of Contents for SpeedRake SR108













































Search results

Summary of Contents for SpeedRake SR108

Reviews:

Related manuals for SpeedRake SR108

Brands by name

Popular brands

KUHN SpeedRake SR108, Operator'S Manual

Search results

Summary of Contents for SpeedRake SR108

Reviews:

Related manuals for SpeedRake SR108

Brands by name

Popular brands