manualshive.com logo in svg

KUHN HR3004D, Operator'S Manual

Share
Download
KUHN HR3004D Operator'S Manual Download Page 67

8. - Instructions for work

HR3004D-3504D

67

KN207JGB_D

Power harrow

8.2

Adjustments in working position

8.2.1 Working depth

The roller provides working depth adjustment and
control.

- Fit the adjustment pin (2) in one of the adjusting

plate holes (1) to adapt the working depth.

-  Adjust both sides to the same setting.

When optional equipment is used, follow
specific procedures mentioned in the related
section:

• Optional equipment / Standard linkage /

Adjustment.

• 

Optional equipment / Hydraulic lift
linkage / Adjustment.

• Optional equipment / Rear attachment

with double acting hydraulic lift /
Adjustments in working position.

•  Optional equipment / Track eradicators /

Adjustments in working position.

• Optional equipment / Front or rear

levelling bar / Adjustments in working
position.

8.3

Machine use

- 

Before leaving the tractor or before
adjusting, maintaining or repairing the
machine, disengage the PTO drive, turn off
the engine, remove ignition key and wait
until all moving parts have come to a
complete stop and apply park brake.

2

1

Summary of Contents for HR3004D

































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands