KUHN HR3004D Operator'S Manual Download Page 64

Page: 64 / 128

HR3004D-3504D

7. - Instructions for transport

KN207JGB_D

Power harrow

7. Instructions for transport

Before placing the machine into transport
position:

- Wait until the rotating parts have come to a

complete stop.

7.1

Putting the machine into
transport position

- When optional equipment is used, follow

specific procedures mentioned in the
related section:
•

Optional equipment / Hydraulic lift
linkage / Putting the machine into
transport position.

• Optional equipment / Rear attachment

with double acting hydraulic lift / Putting
the machine into transport position.

- The transport position is obtained by raising the

tractor's three-point linkage.

The machine is in transport position.

- Never engage the tractor PTO drive when

the machine is in transport position.

Summary of Contents for HR3004D

































































































































Search results

Summary of Contents for HR3004D

Reviews:

Brands by name

Popular brands

KUHN HR3004D, Operator'S Manual

Search results

Summary of Contents for HR3004D

Reviews:

Brands by name

Popular brands