KUHN GMD350 Operator'S Manual Download Page 12

Page: 12 / 100

Disc mower

GMD350 - 350-FF

Safety

Description of symbols

Stage 1:

To measure:

- Tractor tare (T).

For machines with hoppers or tanks:

- If the total unit weight exceeds the tractor Gross Combined Weight Rating in accordance

with the countrie's legislation, empty the hopper to travel on public roads.

- In any case, we recommend to travel on public roads with empty hoppers and tanks.

Description

Units

Description

Tractor unladen weight

PTAC

Gross Combined Weight Rating

Unladen load on tractor front axle

Empty load on tractor rear axle

Axle loads (T machine)

Load on front axle (T machine)

Load on rear axle (T machine)

t1 max

Maximum load authorized on the tractor front axle according to the tires

t2 max

Maximum load authorized on the tractor rear axle according to the tires

Total weight of front tool or front ballast

Summary of Contents for GMD350





































































































Search results

Summary of Contents for GMD350

Reviews:

KUHN GMD350, Operator'S Manual, Page: 12 / 100

Search results

Summary of Contents for GMD350

Reviews: