3
Issue 01 JAN.20
Step 2 - Add Trim to Side Panel
Parts List
Installation Packs
Installation Steps
1 x M193-01
Shim
1 x M305-01
Push-In Seal Pull
Out Tool
1 x FIX-112
4mm Allen Key
2 x No.4x13 CSK
S/S Screws
6 x No.8x30 PH
S/S Screws
6 x 7mm
Wall Plugs
1 x M254-01
No8 Screw Wizard
2 x M224-01
Wallpost Top Cap
2 x
Wall Posts
Step 1 - Install Wall Posts
45mm Deep
30mm Deep
2 x No.6x19 CSK
S/S Screws
1 x FIX-109
2mm Allen Key
2 x SF-BIF-CLMP-998
Rail Clamp
2 x SF-BIF-SLID-998
Centrefold Slider
4 x M6x30 CSK
Hex
1 x M111-03
Installation Spacer
2 x M144-02-AG
Installation Spacer
1 x Rail Left
1 x Rail Right
1 x Door
Assembly
2 x Fixed
Glass Panel
2 x 1940mm
1 x 1926mm
PlexRF-019 Seals
2 x 73mm (800 pack)
2 x 98mm (900, 1000 pack)
1 x 738 (800 Side pack)
1 x 838 (900 Side pack)
WTR-001Trim Seals
1. Position door wall post 21mm in from front edge of the tray,
as shown. Using spirit level to ensure wall post is vertical, mark
through 3 slotted holes per wall post (6 total) onto wall surface.
Remove the post from the tray, placing safely off to one-side.
2. Using a 7mm masonry drill bit and drill (or appropriate drill bit if
drilling tiles), drill six holes using the ‘spot’ marks, each hole should
be 30mm in depth.
3. Insert the six ‘7mm Wall Plugs’ into the six holes. Fix wall post
using 3x No.8 x 30mm long screws provided. Tighten all screws
using pozi-head screwdriver, ensuring the wallpost is vertical.
4. Position side panel wall post 16mm in from front edge of the
tray, as shown. Repeat the above steps.
Insert screw heads into the wizard tool supplied to help locate screws into wall plugs. Then
tighten with pozi head screwdriver.
1. Take note of label on glass
‘
This surface
to outside’
this will determine which is the
bottom edge of your installation.
2a. For 800 Side Panel Unit acquire 1 X
736mm Trim Seal.
2b. For 900 Side Panel Unit acquire 1 X
836mm Trim Seal.
3. Peel off a small length of the bottom trim
adhesive tape and apply to bottom of glass
panel from the edge as shown. Continue
along length of trim, peeling away the tape
as you go, until the full trim length is adhered
to the panel.
1 x 1963mm
PlexRF-018-06
Seal
1 x FIX-111
3mm Allen Key
1 x Side Glass
Panel
Step 3 - Fit Side Panel Glass
1. Carefully fit glass panel into slot in wall
post, ensuring panel is parallel to tray edge.
2. Secure Panel using the Push-in channel.
Remove the protective sleeve on the
push-in channel extrusion. From inside the
enclosure, place the push-in channel (black
strip towards glass) against the glass. At
this stage don’t need to fully insert. Insert
1/4 at the top to secure glass panel whilst
installing.
Push-in channel can be removed, if
necessary, by inserting tool (M305-01)
supplied to pull the channel out at top.
1 x DCM41-01
Corner Bracket
16m
m
21m
m
Fitted Seal to outside
Outside
Position of Side Panel wall post
when fitting on showertray
Position of Door Panel wall post
when fitting on showertray
Mark through 6 (2 x 3) total
slotted holes onto the wall
Inside view
