1-S31
ZD21N-EC, ZD21-EC, ZD28-EC, WSM
ENGINE
(B) Timing Gears, Fuel Camshaft and Camshaft
[D782-E-XFM5]
Injection Pump and Speed Control Plate
1. Remove the socket head screws and nuts, and remove the
injection pump (3).
2. Remove the screws and separate the speed control plate (2),
taking care not to damage the spring (4).
3. Disconnect the spring (4) and remove the speed control plate (2).
(When reassembling)
• Hook the spring (4) to the lever (5) first and install the speed
control plate (2).
• Be sure to place the copper washers underneath two screws (1)
(as shown in the figure).
• Position the slot (9) on the fork lever just under the slot (8) on the
crankcase.
• Insert the injection pump (3) so that the control rod (7) should be
pushed by the spring (6) at its end and the pin (10) on the rod
engages with the slot (9) on the fork lever (as shown in the
figure).
NOTE
■
• The sealant is applied to both sides of the soft metal gasket
shim. The liquid gasket is not required for assembling.
• Addition or reduction of shim (0.05 mm, 0.0020 in.) delays or
advances the injection timing by approx. 0.0087 rad (0.5
°
).
• In disassembling and replacing, be sure to use the same
number of new gasket shims with the same thickness.
W10167080
Fan Drive Pulley
1. Set the stopper to the flywheel.
2. Remove the fan drive pulley retaining screw.
3. Draw out the fan drive pulley with a puller.
(When reassembling)
• Install the pulley to the crankshaft, aligning the mark (1) on them.
• Apply engine oil to the fan drive pulley retaining screws.
And tighten them.
W10172470
(1) Screws and Copper Washers
(2) Speed Control Plate
(3) Injection Pump
(4) Spring
(5) Lever
(6) Spring
(7) Control Rod
(8) Slot (Crankcase Side)
(9) Slot (Fork Lever Side)
(10) Pin
Tightening torque
Fan drive pulley retaining
screw
117.6 to 127.4 N·m
12.0 to 13.0 kgf·m
86.8 to 94.0 ft-lbs
(1) Aligning Mark
KiSC issued 09, 2006 A
Summary of Contents for ZD21-EC
