background image

RT105M Operator’s Manual

Safety - 13

Emergency Procedures

Emergency Procedures 

Before operating any equipment, review emergency procedures and check that all safety precautions have 
been taken.  

Electric Strike Description

When working near electric cables, remember the following:

Electricity follows all paths to ground, not just path of least resistance.

Pipes, hoses, and cables will conduct electricity back to all equipment.

Low voltage current can injure or kill. Many work-related electrocutions result from contact with less 
than 440 volts.

Most electric strikes are not noticeable, but indications of a strike include:

power outage

smoke

explosion

popping noises

arcing electricity

If any of these occur, assume an electric strike has occurred.

Jobsite hazards could cause death or serious injury. Use 

correct equipment and work methods. Use and maintain proper safety 
equipment. 

EMERGENCY SHUTDOWN

 - Turn ignition switch to stop position or push remote engine stop button (if 

equipped).

Electric shock will cause death or serious injury. Stay 

away.          

274-049

Summary of Contents for RT105M
























































































































































































Reviews: