Kubota AP-SR2772 Operator'S Manual Download Page 33

Page: 33 / 44

Section 4: Maintenance & Lubrication

Table of Contents

4/5/19

AP-SRF2772, AP-SRF2790, AP-SR2772, & AP-SR2790 Powered Rakes 321-120MK

12. Clean seal contact edges and apply 1/8" bead of

sealant (Part No. 821-049C) on the chaincase edge
where main cover (#6) contacts chaincase (#10).

13. Install main cover (#6) with 1/4" -20 x 1 1/4" GR2 hex

socket cap screws (#4) and 1/4" -20 x 1 1/2" GR2 hex
socket cap screws (#5). Tighten hex socket cap
screws to the correct torque.

14. Remove top fill plug (#12) and bottom oil level

plug (#18).

15. See

“Chaincase”

on page 28 for gear lube type. Fill

chaincase with specified gear lube through top plug
hole until oil escapes out bottom oil level plug hole.
(Equivalent to 2 1/2 pints.)

16. Install and tighten oil plugs (#12 & #18).

Chaincase Skid Shoe Replacement

Refer to Figure 4-2:

Replace chaincase skid shoe (#1) by removing four
3/8" x 3/4" hex head bolts (#2) and lock washers (#3).

Replace worn skid shoe with new shoe.

Secure skid shoe (#1) with 3/8" lock washers (#3)
and 3/8" x 3/4" GR5 hex head bolts (#2).

Torque hex bolts to the correct torque.

NOTE:

Skid shoe protects chaincase from wear.

Inspect skid shoe frequently and replace as needed.

Chaincase Skid Shoe Replacement

Figure 4-2

39777

Drive Chain Adjustment

Figure 4-1

39774

Change Oil in Chaincase

Refer to Figure 4-1:

Change gear lube every 800 hours or seasonally,
whichever comes first.

Place an oil catch pan under the chain case.

Remove 1 1/4" long hex socket cap screws (#4) and
1 1/2" long hex socket cap screws (#5).

Remove main cover plate (#6) to drain oil.

Clean seal contact edges and apply 1/8" bead of
sealant (Part No. 821-049C) on the chaincase edge
where main cover (#6) contacts chaincase (#10).

Install main cover (#6) with 1/4" -20 x 1 1/4" GR2 hex
socket cap screws (#4) and 1/4" -20 x 1 1/2" GR2 hex
socket cap screws (#5). Tighten hex socket cap
screws to the correct torque.

Remove top fill plug (#12) and bottom oil level
plug (#18).

See

“Chaincase”

on page 32 for gear lube type. Fill

chaincase with specified gear lube through top plug
hole until oil escapes out bottom oil level plug hole.
(Equivalent to 2 1/2 pints.)

Install and tighten oil plugs (#12 & #18).

NOTE:

Oil in chaincase! Be prepared to capture oil

when taking off main cover (#6).

Summary of Contents for AP-SR2772













































Search results

Summary of Contents for AP-SR2772

Reviews:

Related manuals for AP-SR2772

Brands by name

Popular brands

Kubota AP-SR2772, Operator'S Manual

Search results

Summary of Contents for AP-SR2772

Reviews:

Related manuals for AP-SR2772

Brands by name

Popular brands