manualshive.com logo in svg

Kubota AP-SR2772, Operator'S Manual

Share
Download
Kubota AP-SR2772 Operator'S Manual Download Page 20

Section 1: Assembly & Set-up 

Table of Contents

4/5/19

AP-SRF2772, AP-SRF2790, AP-SR2772, & AP-SR2790 Powered Rakes 321-120MK

16

Control Harness With Deutsch 14 Pin Plug

Refer to Figure 1-8:

323-094ADEUTSCH HD30 14 PIN PLUG

If Skid Steer Loader is equipped with a Deutsch 14 Pin 
male connector, then push button control box can be 
eliminated and the Deutsch 14 pin plug & cable (#6) can 
be purchased to connect the solenoid directly to the Skid 
Steer Loader controls.

1.

Connect red wire plug (#3) to bottom solenoid 
connector (#4).

2.

Connect green wire plug (#1) to top solenoid 
connector (#2).

3.

Attach Deutsch 14 pin plug (#7) to the skid steer’s 
Deutsch 14 pin male plug. 

4.

Zip ties (#5) will be installed later.

5.

Skip to 

“Operational Check” 

on page 18.

.

Deutsch 14 Pin Plug & Cable

Figure 1-8

39766

Electrical Control Harness (Optional)

Kubota offers three electrical control wire harnesses for the purpose of operating the hydraulic angling cylinder. If not 
purchased with the Powered Rake, one may be purchased from your nearest Kubota dealer.

•

Part No. 323-094A - - - - - - - - - - - - - - - - Wire harness with Deutsch 14 pin power plug. 

 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to 

“Control Harness With Deutsch 14 Pin Plug”

 below.

•

Part No. 323-096A - - - - - - - - - - - - - - - - Switch & wire harness with Deutsch 2 pin power plug. 

 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to 

“Control Harness With Deutsch 2 Pin Plug” 

on page 17.

•

Part No. 323-097A - - - - - - - - - - - - - - - - Switch & wire harness with eyelets for connecting to 12V power source. 

 - - - - - - - - - - - - - - - - - - - - - - - - - - - - - Refer to 

“Control Harness With 2 Eyelets” 

on page 18.

Kubota offers two controllers for operating the Powered Rake when attached to a Kubota compact track loader or skid 
steer loader. See your nearest Kubota dealer to purchase one of their controllers.

•

Part No. V0511-97010  - - - - - - - - - - - - - SVL Electrical connector (2 functions)

•

Part No. W/G S6699 - - - - - - - - - - - - - - - SVL Multifunction handle (7 functions)

Kubota Hose Routing (SVL Shown)

Figure 1-7

37388

9

8

11

Summary of Contents for AP-SR2772













































Reviews:

No comments

Brands by name

Popular brands

Load more brands