KTR-Group BoWex junior plug-in Operating & Assembly Instructions Download Page 21

Page: 21 / 22

BoWex

Operating/Assembly instructions

KTR-N
Sheet:
Edition:

40110 EN
21 of 22
16

Please observe protection

note ISO 16016.

Drawn:

2019-07-01 Pz/Wb

Replacing:

KTR-N dated 2017-01-02

Verified:

2019-07-23 Pz

Replaced by:

Substance group - gases, fogs and vapours:

The marking with explosion group llC includes the explosion groups llA and llB.

Substance group - dusts:

The marking with explosion group lIlC includes the explosion groups lIlA and lIlB.

If the symbol

was punched in addition to marking

, the coupling component was supplied by KTR as an

unbored or pilot bored version (see chapter 4.2 of the present operating/assembly instructions).

Enclosure A

Advice and instructions regarding the use in

potentially explosive atmospheres

9.5

marking of coupling for potentially explosive atmospheres

Summary of Contents for BoWex junior plug-in























Search results

Summary of Contents for BoWex junior plug-in

Reviews:

Related manuals for BoWex junior plug-in

Brands by name

Popular brands

KTR-Group BoWex junior plug-in, Operating & Assembly Instructions

Search results

Summary of Contents for BoWex junior plug-in

Reviews:

Related manuals for BoWex junior plug-in

Brands by name

Popular brands