manualshive.com logo in svg

KTM SXF 350, Owner'S Manual

Share
Download
KTM SXF 350 Owner'S Manual Download Page 19

PREPARING FOR USE

17

600868-01

–

Clean the chain.

Chain cleaner (

p. 94)

–

Fit the steel sprocket.

Tip

Do not grease the chain.

–

Clean radiator fins.

–

Straighten bent radiator fins carefully.

–

If used in sand regularly, replace the piston every 20 operating hours.

6.5

Preparing for rides on wet sand

–

Seal the air filter box.

x

Tip

Seal the air filter box on the edges against dirt.

–

Clean the air filter and air filter box.

x

(

p. 43)

Info

Check the air filter approx. every 30 minutes.

B00437-01

–

Fit a waterproofing device on the air filter.

Waterproofing device for air filter (77206921000)

Info

See the

KTM PowerParts

fitting instructions.

600868-01

–

Clean the chain.

Chain cleaner (

p. 94)

–

Fit the steel sprocket.

Tip

Do not grease the chain.

–

Clean radiator fins.

–

Straighten bent radiator fins carefully.

–

If used in sand regularly, replace the piston every 20 operating hours.

6.6

Preparing for rides on wet and muddy surfaces

–

Seal the air filter box.

x

Tip

Seal the air filter box on the edges against dirt.

–

Clean the air filter and air filter box.

x

(

p. 43)

Info

Check the air filter approx. every 30 minutes.

Summary of Contents for SXF 350







































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands