KTI Networks KGS-1260/G Installation Manual Download Page 32

Page: 32 / 34

-32-

RFC 4188 - Bridge MIB

RFC 4668 - RADIUS Authentication Client MIB

RFC 5519 - Multicast Group Membership Discovery (MGMD) MIB

IEEE 802.1 MSTP MIB

IEEE 802.1AB LLDP MIB

IEEE 802.1X Port Access Entity (PAE) MIB

TIA 1057 LLDP Media Endpoint Discovery (MED) MIB

IEEE 802.1-Q-BRIDGE MIB

Private SFPDDM MIB (Read DDM status of the SFP ports)

Private reboot MIB (Remote boot over SNMP)

Private TFTP firmware update MIB (TFTP Firmware update over SNMP)

Private OPA function MIB (OPA configuration for the SFP ports)

Private ALS function MIB (ALS configuration for the SFP ports)

One product MIB file is also available in the product CD for SNMP manager software.

4.6.1 SNMP Traps

In addition to the SNMP standard traps, the device is equipped with private OPA alarm traps.

The traps are:

Alarm trap – Port TX power lower than the minimal value

Alarm trap – Port TX power higher than the maximal value

Normal trap – Port TX power back to normal (higher than the minimal value)

Normal trap – Port TX power back to normal (lower than the maximal value)

Summary of Contents for KGS-1260/G



































Search results

Summary of Contents for KGS-1260/G

Reviews:

Related manuals for KGS-1260/G

Brands by name

Popular brands

KTI Networks KGS-1260/G, Installation Manual

Search results

Summary of Contents for KGS-1260/G

Reviews:

Related manuals for KGS-1260/G

Brands by name

Popular brands