KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K User Manual Download

Page: 2 / 50

Class B EMC Statements

(High Voltage Models up to 3000 VA)

FCC Part 15

NOTE This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may

cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation. If this equipment does cause harmful

interference to radio or television reception, which can be determined by turning the equipment off

and on, the user is encouraged to try to correct the interference by one or more of the following

measures:

● Reorient or relocate the receiving antenna.

● Increase the separation between the equipment and the receiver.

● Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

● Consult the dealer or an experienced radio/TV technician for help.

Summary of Contents for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K



















































Search results

Summary of Contents for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Reviews:

Related manuals for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Brands by name

Popular brands

KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K, User Manual

Search results

Summary of Contents for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Reviews:

Related manuals for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Brands by name

Popular brands