KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K User Manual Download | Manualshive

Page: 14 / 50

background image

14

the top and

bottom of the EBP front cover. See Figure

12

for the location of the EBP cable knockouts.

CAUTION
A small amount of arcing may occur when connecting an EBP to the UPS. This is normal and will not

harm personnel. Insert the EBP cable into the UPS battery connector quickly and firmly.

5.

Plug the EBP cable(s) into the battery connector(s) as shown in Figure

12

. Up to four EBPS may be

connected to the UPS.

Connect black to black,. Press the connector tightly together to ensure a

proper connection.
To connect a second EBP, unclip the EBP connector on the first EBP and pull gently to extend the

wiring to the EBP connector on the second EBP. Repeat for any additional EBPS.

6.

Verify that the EBP connections are tight and the adequate bend radius and strain relief exist for

each cable.

Figure12 Typical EBP Installation

7.

Replace the EBP front cover.

To replace the cover, verify that the EBP cables are routed through the EBP cover knockouts, cover

connects with the cover hook near the left side of the EBP cabinet. Repeat for each additional EBP.
It is the same with the installation of the front cover. (Refer” to UPS installation”)

8.

Verify that all wires connected between the UPS and EBP(s) are installed behind the front covers

and not accessible to users.

9.

Return to Step 4 to continue the UPS installation.

0T

Rackmount converted to Tower

Installation

1

.

0T

Rackmount converted to Tower

0T

plastic base installation

«
...
12
13
14
15
16
...
»

Summary of Contents for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K



















































Reviews:

No comments

Related manuals for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

F6C.B550.750AVRT

Brand: Belkin Pages: 2

HURON PRO HR1000

Brand: Aston Global Pages: 4

Brand: Trust Pages: 2

Brand: Chloride Pages: 144

Brand: Tripp Lite Pages: 12

Brand: Tripp Lite Pages: 36

Brand: Tripp Lite Pages: 44

Tripp-Lite 1109502801

Brand: Adaptive Pages: 6

Brand: Borri Pages: 60

Brand: LEGRAND Pages: 52

SLC TWIN series

Brand: Salicru Pages: 61

Brand: KEHUA TECH Pages: 123

Brand: Eaton Pages: 7

Brand: Eaton Pages: 25

TRIPP LITE Series

Brand: Eaton Pages: 78

Brand: Eaton Pages: 52

UPS5000-A-500 kVA

Brand: Huawei Pages: 187

UPS5000-E-360 kVA

Brand: Huawei Pages: 239

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands