KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K User Manual Download

Page: 43 / 50

discharges the batteries for 10 seconds. The LED indicators of the front cover stop cycling when the

test is completed.

Recycling the Used Battery or UPS

Contact your local recycling or hazardous waste center for information on proper

disposal of the used battery or UPS.

WARNING



Do not dispose of the battery or batteries in a fire. Batteries may explode.

Proper disposal of batteries is required. Refer to your local codes for disposal

requirements.



Do not open or mutilate the battery or batteries. Released electrolyte is harmful

to the skin and eyes. It may be toxic.

CAUTION

Do not discard the UPS or the UPS batteries in the trash. This product contains

sealed,lead‐acid batteries and must be disposed properly. For more information,

contact your local recycling/reuse or hazardous waste center

CAUTION

Do not discard waste electrical or electronic equipment (WEEE) in the trash. For

proper disposal, contact your local recycling/reuse or hazardous waste center.

Summary of Contents for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K



















































Search results

Summary of Contents for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Reviews:

Related manuals for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Brands by name

Popular brands

KStar MEMO PLUS RT II (MP9100RTII-0.9) 1-3K, User Manual

Search results

Summary of Contents for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Reviews:

Related manuals for MEMO PLUS RT II (MP9100RTII-0.9) 1-3K

Brands by name

Popular brands