KSB Meganorm, Operation Manual

Page: 3 / 16

3
Meganorm
6. Technical data
Pump sizes
Technical data
Units.
25-150 25-200
d
32-125.
1
32-125 32-160.
1
32-160 32-200.
1
d
32-200
d
40-125 40-160 40-200
d
50-125 50-160 50-200
d
65-125 32-250.
1
d
32-250
d
40-250
d
50-250
d
65-160 65-200
d
80-160 40-315 50-315 65-250
d
80-200
d
80-250
d
100-16
0
100-20
0
d
65-315 80-315 80-400
e
100-25
0 *
100-31
5
100-40
0
e
125-20
0 *
125-25
0
125-31
5
125-40
0
e
150-20
0
150-25
0
150-31
5
150-40
0
e
Bearing bracket A 30 A 40 A 50 A60
mm
5,5
6 7 9 5 5 6 6
14 12
9
20 16 11 25
8 8 8
12 21 17 31
9 9
13 23 19 36 32 13 18 13 27 23 17 40 37 30 25 59 48 39 33
Width of impeller
passage
inch
3/16 4/16 4/16 6/16 3/16 3/16 4/16 4/16 9/16 8/16 6/16
13/16 10/16
7/16
1
5/16 5/16 5/16 8/16
13/16 11/16
1 4/16
6/16 6/16 8/16
14/16 12/16
1 7/16 1 4/16
8/16
10/16
8/16
1 1/16
14/16 11/16
1 9/16 1 7/16 1 3/16
1
2 5/16
1 14/16
1 9/16 1 5/16
kg m²
0.0214 0.0591 0.0140 0.0142 0.0224 0.0238 0.0760 0.0786 0.0144 0.0336 0.0640 0.0189 0.0394 0.0750 0.0263 0.1800 0.1820 0.1880 0.1920 0.0521 0.0985 0.0641 0.4396 0.4800 0.2232 0.1568 0.2904 0.1040 0.1800 0.5120 0.5696 1.2788 0.3172 0.6100 1.3832 0.2230 0.4100 0.7740 1.6912 0.2918 0.4656 0.8680 1.8600
WR
2
with water
lb.ft
2
0.127 0.350 0.083 0.084 0.132 0.141 0.451 0.466 0.085 0.199 0.379 0.112 0.233 0.445 0.156 1.068 1.079 1.115 1.139 0.309 0.584 0.380 2.608 2.847 1.324 0.930 1.722 0.617 1.067 3.037 3.379 7.587 1.881 3.619 8.206 1.323 2.432 4.592
10.033
1.731 2.762 5.149
11.035
Max. rot. speed rpm 3500 1750 3500 1750
Max. suction pressure bar/(psi) 10 / (145)
d e
Max. discharge pressure
x Temp.
bar/(psi) See table 7
mm 10 12,5
Packing
inch 3/8 1/2
Shaft
Seal
Mech. seal
f
inch 1 3/8 1 3/4 2 3/8 2 3/4
Axial thrust balance -
c
By bored hole on impeller
Min./max. flow - 0.1 Qopt / 1.1 Qopt 0.15 Qopt / 1.1 Qopt
Flanges - ANSI B 16.1 125 Lb FF 250 Lb FF 125LbFF
y y y yy
ANSI B 16.1 125 Lb FF
Rotation direction - Clockwise, seen from driver end
Ball bearings 2x 6306 C 3 6308 C 3 6310 C 3
6312 C
3
Bearings
Lubrication Oil
Drive (P/n value)
Shaft SAE 1045
HP/rpm 0.0176 0.0458 0.100
0.158
kg
32 40 34 35 34 34 42 44 38 38 49 40 42 47 49 68 68 73 72 70 61 89
104 108
89 92
106 105 108 126 132 162 132 142 178 136 157 156 193 183 192 246 280
Weight Cast iron
lb
70 88 75 77 75 75 92 97 84 84
108
88 92
104 108 150 150 161 159 154 134 196 229 238 196 202 233 231 238 278 291 357 291 313 392 300 346 344 425 403 423 542 617
Table 1 y
125Lb FF
yy
250 Lb FF
*For sizes 100-250 and 125-200 max. speed = 2.900 rpm.
c
For size 25-200 by bored holes on impeller, for sizes 25-150; 32-125.1 and 32-125 without axial thrust balance.
de
The maximum suction pressure for pumps with mechanical seal is 5 bar (73 psi), except for sizes
d
in 3500 rpm
and
e
in 1750 rpm which are limited by sum of inlet pressure and work pressure not exceeding 10 bar (145 psi).
f
Materials: stationary face in ceramic, rotating face in carbon, seals in Buna-N.
Not recommended for liquids containing solids.
Other materials upon request.