Krups EA871, Manual

Page: 27 / 180

29 28
ENGLISH
PROBLEM CORRECTIVE ACTIONS
O
per
ation
The machine displays a fault, the
software is frozen.
OR
Your machine has a malfunction.
Turn off and unplug the machine, remove the filter cartridge, wait 1
minute and restart the machine.
Press and hold the ON/OFF button for at least 3 seconds for starting.
The appliance does not turn
on after pressing the ON/OFF
button (for at least 3 seconds).
Check the fuses and the power socket of your electrical installation.
Check that the two power plugs are correctly inserted into the socket.
A power failure has occurred
during a cycle.
The appliance resets automatically when it turns back on.
The grinder stops during recipe
with beans LED lit.
Add beans and press start again.
Grinder turns empty. Machine self-learning.
Us
e
The grinder makes an abnormal
noise.
Foreign bodies are surely present in the grinder.
There is water under the device. Before removing the water tank, wait 1 5 seconds after the fl ow of
coffee so that the machine finishes its cycle correctly.
Verify that the drip tray is well positioned on the machine. It must
always be in place even when the machine is not in use.
Verify that the drip tray is not full.
The adjustment button for the
grinding fineness is di ffi cult to
turn.
Turn the adjustment button of the grinding fineness only when the
grinder is operating.
The device has not issued any
coffee.
An incident has been detected during its making.
The device is reset automatically and is ready for a new cycle.
You have used ground coffee
instead of coffee beans.
Use your vacuum cleaner to collect the ground coffee contained in
the bean container.
Water runs from the coffee
nozzles when the machine stops.
Automatic rinsing to clean the coffee nozzles and prevent clogging.
ANSWERS TO YOUR QUESTIONS
– Launching a recipe
– Out of beans detection: light alert (W), alert + grinder stops
– Fill the coffee bean container with coffee beans
– Press " START/STOP "
– Restarts the recipe, to avoid wasting coffee.
Caution: The use of oily coffee can lead to erroneous detection due to poor bean throughput. If detection
activates, simply press the START/STOP button again to continue the recipe.
The function can be manually disabled (see “ OTHER FUNCTIONS ” - “ Disable the beans missing function ” ).
PROBLEM CORRECTIVE ACTIONS
Ste
am
The milk frothing accessory
makes a noise.
Check that the milk frothing accessory is correctly positioned on its
non-removable attachment fixed to the machine (G3).
The milk frothing accessory on
your machine seems partly/
completely blocked
OR if the milky recipe or hot
water stops prematurely and the
front panel alert fl ashes.
Make sure that your milk frothing accessory is not blocked by milk or
chalky residues. Unclog the holes with the needle supplied with your
appliance. See chapter 6 - CLEANING THE MILK FROTHING ACCESSORY,
figs 1 to 8.
The milk frothing accessory does
not or does not make much milk
froth.
For milk-based preparations, we advise you to use fresh, pasteurised
or UHT milk, recently opened. We also recommend using a cold
container.
Nothing comes out of the milk
frothing accessory.
a. When frothing milk for the first time, if nothing comes out correctly.
• Check that the milk frothing accessory is not blocked. See
above: " The accessory of your machine appears to be partially or
completely blocked.
• Perform the following protocol once only:
• Empty the water tank and temporarily remove the Claris Aqua Filter
System cartridge. Fill the tank with mineral water high in calcium
( > 100mg/L) and make successive steam cycles ( 5 to 10 cycles) in
a container until a continuous jet of steam is obtained. Put the
cartridge back in the tank.
b. The milk frothing accessory had previously worked:
• Ensure that the accessory output is not blocked. See above: " The
outlet of your machine ' s milk frothing accessory appears to be
partially or completely blocked " .
If after completing the above steps it still does not work, please
contact your service centre.
Water or steam comes out of the
milk frothing attachment.
Check that the milk frothing accessory is correctly positioned on
its non-removable attachment fixed to the machine (G3). At the
beginning or end of the recipe, a few drops may fl ow through the
accessory.
Appearance of steam under the
bean tray lid.
Close the cleaning tablet funnel located under the lid. (J)
M
ain
tenanc
e
The machine does not request
descaling.
The descaling cycle is requested from a large number of uses of the
steam circuit.
Some grounds are in the drip
tray.
A small amount of ground coffee can get into the drip tray. The
machine is designed to evacuate any excess ground coffee so that the
percolation zone remains clean.
The light alerts are still lit up after
you have emptied the coffee
grounds tray.
Reinstall the coffee grounds collector.
M
ain
tenanc
e
After filling the water tank, the
light alerts remain on.
Check the correct positioning of the tank in the device.
The fl oats at the bottom of the tank must move freely. Check and
unlock the fl oats if necessary.