Krone Swadro 38 T Original Operating Instructions Download Page 38 | Manualshive

Page: 38 / 66

Krone Swadro 38 T Original Operating Instructions Download Page 38

Operation

38

Pos : 74 /Ü bersc hriften/Übersc hriften 2/P-T/Sc hwadfor mer @ 7\mod_1215506811417_78.doc @ 102676

8.4

Swath former

Pos : 75 /BA/Sic her heit/Gefahr enhi nweis e/Sc hwader /Gefahr Sc hwenkber eich @ 7\mod_1215503895526_78.doc @ 102545

Danger! - Before swivelling the machine, ensure that nobody is within the swivel range.

Effect: Danger to life or serious injuries.
•

Instruct persons to leave the danger zone.

•

If required, switch off the machine immediately.

Do not work on the machine until the engine is at a standstill.
•

Switch off the engine and remove the ignition key.

•

Secure the tractor and machine against rolling.

Pos : 76 /BA/Bedi enung /Schwader/Sc hwadtuc h/Schwadfor mer/Schwadfor mer dem Futter anpass en SW 710T @ 7\mod_1215506647433_78.doc @ 102656

The distance from the swath former to the rotor can be adjusted for

narrow or wide swathing or

can be adjusted continuously to the amount of forage. The distance from the swath former to
the rotor must be adjusted to the amount of forage.

High amount of forage = long distance
Small amount of forage = short distance

Pos : 77 /BA/-----Sei tenumbruch------ @ 0\mod_1196175311226_0.doc @ 4165

«
...
36
37
38
39
40
...
»

Summary of Contents for Swadro 38 T



































































Reviews:

No comments