Krone Swadro 38 T Original Operating Instructions Download Page 35

Page: 35 / 66

Driving and Transport

Pos : 55 /Ü bersc hriften/Übersc hriften 2/P-T/Tr ansportvorbereitung @ 5\mod_1213247130420_78.doc @ 87570

7.1

Preparation for transport

Pos : 56 /BA/F ahren und Tr ansport/Sc hwader /Vorbereitung für den Trans port Swadro 46 T Bild US @ 10\mod_1221053093200_78.doc @ 131826

SW46T029_US

Figure 13:

Pos : 57 /BA/F ahren und Tr ansport/Sc hwader /Vorbereitung für den Trans port Swadro 46 T T ext @ 10\mod_1221052940137_78.doc @ 131804

•

Machine must be completely and correctly hitched (see chapter on Start-up entitled
"Attaching to the Tractor").

•

Machine must be in the transport position (see chapter on operation entitled "From
Working Position to Transport Position").

•

Raise the rotors with the control valve for transport.

Pos : 58 /Abkürzungen /Abkürzungen s prac hneutr al/Schwader/Swadro 46 T @ 8\mod_1219389700439_0.doc @ 117407

Swadro 46T

Pos : 59 /BA/F ahren und Tr ansport/Sc hwader /Hinweis Zi nkenarme umkl appen @ 7\mod_1215751987985_78.doc @ 105296

Note

Make certain:

•

the 7 tine arms (3) (4 tine arms on the left and 3 tine arms on the right)
are always swivelled into transport position.

•

the rotor is secured by rotation lock (A).

Pos : 60 /BA/-----Sei tenumbruch------ @ 0\mod_1196175311226_0.doc @ 4165

Summary of Contents for Swadro 38 T



































































Search results

Summary of Contents for Swadro 38 T

Reviews:

Krone Swadro 38 T, Original Operating Instructions, Page: 35 / 66

Search results

Summary of Contents for Swadro 38 T

Reviews: