Krone EasyCut F 320 Original Operating Instructions Download Page 75

Page: 75 / 86

Maintenance - Lubrication

Lubrication chart - Machine

15.2

Original Operating Instructions 150000802_00_en

Lubricating intermediate universal shaft

KMG000-069

The machine is shut down and safeguarded,

refer to page 23

Lubricate the universal shaft with multi-purpose grease at the intervals indicated in the

figure.

15.2

Lubrication chart - Machine

The information on maintenance intervals is based on average load of the machine. In case of

an increased load and under extreme working conditions, the time periods must be reduced.

The types of lubrication are marked by means of icons in the lubrication chart, refer to table.

Type of lubrication

Lubricant

Note

Grease

Multi-purpose grease

• Two strokes from the

grease gun per grease

nipple.

• Remove superfluous

grease at the lubrication

nipple.

KMG000-084

Summary of Contents for EasyCut F 320























































































Search results

Summary of Contents for EasyCut F 320

Reviews:

Related manuals for EasyCut F 320

Brands by name

Popular brands

Krone EasyCut F 320, Original Operating Instructions

Search results

Summary of Contents for EasyCut F 320

Reviews:

Related manuals for EasyCut F 320

Brands by name

Popular brands