manualshive.com logo in svg

Krone EasyCut F 320, Original Operating Instructions

Share
Download
Krone EasyCut F 320 Original Operating Instructions Download Page 38

7

Start-up

7.1

Preparing tractor

38

Original Operating Instructions 150000802_00_en

7

Start-up

 WARNING

Risk of injury due to non-observance of relevant safety instructions

If the relevant safety instructions are not observed, persons may be seriously injured or killed.

„

To avoid accidents, the relevant safety instructions must be read and observed, 

refer to

page 12

.

 WARNING

Risk of injury due to non-observance of safety instructions

If the relevant safety routines are not observed, persons may be seriously injured or killed.

„

The safety routines must be read and observed to avoid accidents, 

refer to page 23

.

 WARNING

Risk of injury or damage to the machine caused by connection lines that are not

connected or laid properly

If the connection lines of the machine are not connected or laid properly to the tractor they

may tear off or may be damaged. This may result in serious accidents.

„

Connect and secure the hoses and cables properly.

„

Lay the hoses, cables and ropes so that they do not rub, tension, pinch or touch other

parts (e.g. tractor tyres), especially when cornering.

7.1

Preparing tractor

„

Change the front lifting unit over to single-acting.

„

Disconnect the lower links from the swing position.

„

Move the front axle suspension of the tractor to the central position and deactivate it.

7.2

Connecting machine to tractor

KMG000-049

Summary of Contents for EasyCut F 320























































































Reviews:

No comments

Brands by name

Popular brands

Load more brands