KROMBACH TUFSEAT Performance Series Installation, Operation And Maintenance Manual Download Page 25

Page: 25 / 28

www.cranecpe.com

4. Insert the SHC screw through the locking plate hole and
hand lever and tighten the hex nut until snug, clamping the
hand lever to the stem flats (Figure 4).

5. Insert locking pin thru locking pin hole on lever (Figure 4 &
5).
6. Attach the retaining ring in groove near the bottom of lock-
ing pin (Figure 5). This will assure the locking pin is attached
to the lever.

Installing Lockout Padlock (provided by
customer)

1. Using padlock with 8 mm shank, insert shank thru the elon-
gated hole in locking plate and hole under pull ring (Figure 6).

2. Using padlock with 6 mm shank, insert shank thru the hole
in locking pin under the hand lever ear (Figure 7).

ATTENTION

Do not over tighten Socket Head Cap (SHC) Screw/Hex Nut.
Excessive torque may fracture screw and could result in
minor injury or property damage!
Size M6 thread, max bolt torque= 54 in-lbs or 6 Nm
Size M10 thread, max bolt torque=248 in-lbs or 28 Nm
Size M16 thread, max bolt torque=1072 in-lb or 121 Nm

Instructions for Mounting Hand Lever and Locking Device

Using padlock with 8 mm shank

Using padlock with 6 mm shank (no need for Locking plate)

Locking plate

Locking pin

Hand lever

Stem

Socket Head Cap Screw (Stop pin)

Hex nut

Socket Head Cap Screw (SHCS)

Stem flats

Retaining ring

Stop pin

Stem flats

Hand lever

Hex nut

SHC Screw

Locking plate

Locking pin

Retaining ring

Locking pin

Hand lever

Stop pin

Stem flats

Hex nut

SHC Screw

Locking pin

Retaining ring

Padlock 6mm

Locking pin

Locking plate

Hex nut

SHC Screw

Hand lever ear

Hole for SHC screw

Stop pin

Oval handle

Figure 1

Figure 4

Figure 2

Figure 3

Figure 5

Figure 7

Locking plate

Locking pin

Figure 6

Padlock 8mm

Using padlock with 8 mm shank

Using padlock with 6 mm shank (no need for Locking plate)

Locking plate

Locking pin

Hand lever

Stem

Socket Head Cap Screw (Stop pin)

Hex nut

Socket Head Cap Screw (SHCS)

Stem flats

Retaining ring

Stop pin

Stem flats

Hand lever

Hex nut

SHC Screw

Locking plate

Locking pin

Retaining ring

Locking pin

Hand lever

Stop pin

Stem flats

Hex nut

SHC Screw

Locking pin

Retaining ring

Padlock 6mm

Locking pin

Locking plate

Hex nut

SHC Screw

Hand lever ear

Hole for SHC screw

Stop pin

Oval handle

Figure 1

Figure 4

Figure 2

Figure 3

Figure 5

Figure 7

Locking plate

Locking pin

Figure 6

Padlock 8mm

Figure 6

Figure 7

Locking pin

Padlock 8 mm

Locking pin

Padlock 8 mm

Locking plate

Using padlock with 8 mm shank

Using padlock with 6 mm shank (no need for Locking plate)

Locking plate

Locking pin

Hand lever

Stem

Socket Head Cap Screw (Stop pin)

Hex nut

Socket Head Cap Screw (SHCS)

Stem flats

Retaining ring

Stop pin

Stem flats

Hand lever

Hex nut

SHC Screw

Locking plate

Locking pin

Retaining ring

Locking pin

Hand lever

Stop pin

Stem flats

Hex nut

SHC Screw

Locking pin

Retaining ring

Padlock 6mm

Locking pin

Locking plate

Hex nut

SHC Screw

Hand lever ear

Hole for SHC screw

Stop pin

Oval handle

Figure 1

Figure 4

Figure 2

Figure 3

Figure 5

Figure 7

Locking plate

Locking pin

Figure 6

Padlock 8mm

Figure 5

Locking plate

Retaining ring

Locking pin

Using padlock with 8 mm shank

Using padlock with 6 mm shank (no need for Locking plate)

Locking plate

Locking pin

Hand lever

Stem

Socket Head Cap Screw (Stop pin)

Hex nut

Socket Head Cap Screw (SHCS)

Stem flats

Retaining ring

Stop pin

Stem flats

Hand lever

Hex nut

SHC Screw

Locking plate

Locking pin

Retaining ring

Locking pin

Hand lever

Stop pin

Stem flats

Hex nut

SHC Screw

Locking pin

Retaining ring

Padlock 6mm

Locking pin

Locking plate

Hex nut

SHC Screw

Hand lever ear

Hole for SHC screw

Stop pin

Oval handle

Figure 1

Figure 4

Figure 2

Figure 3

Figure 5

Figure 7

Locking plate

Locking pin

Figure 6

Padlock 8mm

Figure 4

Hex nut

Locking plate

SHC Screw

Summary of Contents for TUFSEAT Performance Series





























Search results

Summary of Contents for TUFSEAT Performance Series

Reviews:

Related manuals for TUFSEAT Performance Series

Brands by name

Popular brands

KROMBACH TUFSEAT Performance Series, Installation, Operation And Maintenance Manual

Search results

Summary of Contents for TUFSEAT Performance Series

Reviews:

Related manuals for TUFSEAT Performance Series

Brands by name

Popular brands