KROMBACH TUFSEAT Performance Series Installation, Operation And Maintenance Manual Download Page 19 | Manualshive

Page: 19 / 28

background image

19

www.cranecpe.com

Assembly of KFO-1156 High Temperature Trim Floating Ball Valve

KFO1156: High Temperature Trim

Figure 8

1. Apply Castrol Optimal paste on short threaded part of the
Studs (#10) and insert them into the Body tap holes. Then
tighten the Studs.

2. Insert S2 stem seal (#7) over the top of the stem (#4) with
the conical surface facing the spherical stem shoulder, slide
the S2 Seal over the spherical portion of the stem (see Fig. 8).

3. Insert Stem (#4) through the valve body cavity, allowing the
S2 Stem Seal (#7) to be seated into the body counter bore.

4. Install one number of graphite packing ring (thick) &
diffusion barrier ring (thin) (#13) over the stem (#4).

5. Grease contact surfaces of gland bushing (#14) and the
packing gland (#8) and then insert them onto the stem and
push the stem seals deeper into the stem chamber.

«
...
17
18
19
20
21
...
»

Summary of Contents for TUFSEAT Performance Series





























Reviews:

No comments

Related manuals for TUFSEAT Performance Series

Brand: Samson Pages: 52

Brand: Samson Pages: 32

Brand: Danfoss Pages: 59

Brand: QUNDIS Pages: 2

Brand: FEAS Pages: 4

Brand: Baier Pages: 20

RM-LUM-M320-IT/A

Brand: Grosvenor Pages: 2

Calc-An-Acre II

Brand: micro-trak Pages: 30

Ecomat100 CR1055

Brand: IFM Pages: 32

PersonalWorkplace Pro Video

Brand: G&D Pages: 56

Brand: Beninca Pages: 16

Brand: Woodward Pages: 118

Brand: Pangolin Pages: 35

Brand: Nibe Pages: 92

Brand: Ubiquiti Pages: 16

Markoprint iJET

Brand: Weber Pages: 127

Easyflow J7 DN15

Brand: Neles Pages: 12

Brand: Estyma Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands